FAQ Search Results
The connection fails often, even though it is possible to reconnect each time. How can I improve the connection?
Try the following tips:
1. Reduce the distance to the installed (and previously connected) SMART HUB-150.
2. Disconnect any devices that are connected unnecessarily.
3. Make sure the Bluetooth connection is not disrupted by a material like metal or a microwave or Wi-Fi router.
The cable of my fixture is damaged. Can I repair it?
Absolutely. Use the WATERLOCK accessory. The WATERLOCK lets you repair damaged fixture cables. To fix the cable, perform the following steps:
11. First make sure that the power supply to the cable is switched off.
12. Use small 4/6 mm² screw terminals no larger than 18 mm x 12 mm x 16 mm.
13. Cut the cable to size using cable cutters or a wire stripper. Is the cable damaged? Cut past the damaged section.
14. Use a fitting screwdriver to loosen the screws on one side of the screw terminal.
15. Insert the copper cable wire on one side of the screw terminal.
16. When connecting, make sure the entire copper wire is inside the screw terminal, so that only the plastic casing is visible.
17. Repeat steps 5 and 6 for the other cable. Important: Connect the right colors of the screw terminal together.
18. Tighten the screws again.
19. Place the screw terminal in the middle of the WATERLOCK. It is filled with gel to ensure a 100% waterproof connection.
20. Close the WATERLOCK securely, making sure you hear a “click”.
Important: The WATERLOCK cannot be used to repair in-lite main cables (CBL 14/2 and CBL 10/2).
How is the DISC WALL 100-230V dimmed?
With an external LED dimmer only. Connect the DISC WALL 100-230V to an external LED dimmer with trailing edge and a wattage of 2-100W or 3-100W.
Does the DISC PENDANT 100-230V require an external LED dimmer?
No, the DISC PENDANT 100-230V does not require an external dimmer. It is dimmable without an external LED dimmer. In other words, the light does not have to be connected to a switched power outlet.
Can an external switch be connected to the DISC PENDANT 100-230V?
Yes, it can. But this may not be an LED dimmer.
Important: If you want to use an external switch, keep in mind that when the switch is in the OFF position, the light cannot be operated by the sensor. Also, the light will be subjected to an automatic calibration process the first 15 seconds each time the external switch is switched from the OFF to the ON position. During this time, do not place a hand or conductive objects near the sensor because this will interfere with calibration.
How can I dim the DISC PENDANT 100-230V?
The DISC PENDANT 100-230V is dimmable by hand movement. The sensor is located on the bottom of the fixture in the middle and is operated by hand approach.
Brief touch/approach: On/Off
Long touch/approach: Dim
The dimmer remembers the last position when switched off manually by the sensor.
What happens if the DISC PENDANT 100-230V is disconnected from the power supply?
If disconnected from the power supply completely (using, for example, an extra switch) and then reconnected, the light will be in the highest setting when switched on by hand movement. The light will also be subjected to an automatic calibration process the first 15 seconds each time it is disconnected from the power supply. During this time, do not place a hand or conductive objects near the sensor because this will interfere with calibration.
Can the DISC PENDANT also be installed directly in or on the ceiling?
No, this is not possible. The DISC PENDANT is installed using a strain relief. The plug provided can be used on the end of the cable after guiding it through the ceiling.
How high should I hang the DISC PENDANT (100-230V)?
The DISC PENDANT can be adjusted to different heights as desired.
Important: The maximum cable length is 220 cm.
Is the DISC PENDANT (100-230V) weather-resistant?
Yes, the DISC PENDANT (100-230V) is waterproof and designed to withstand the elements.
Can the DISC BASE and DISC BASE TRIPLE also be used for the DISC PENDANT?
No, the DISC BASE and DISC BASE TRIPLE can only be used with the DISC PENDANT 100-230V.
Can the DISC PENDANT 100-230V fixtures that are combined using the DISC BASE TRIPLE be operated separately?
Yes, they can. The DISC PENDANT 100-230V fixtures can be operated separately.
I've accidentally cut my fixture cable. Can I fix it?
Absolutely. Use the WATERLOCK accessory. The WATERLOCK lets you repair cut fixture cables. To fix the cable, perform the following steps:
1. First make sure that the power supply to the cable is switched off.
2. Use small 4/6 mm² screw terminals no larger than 18 mm x 12 mm x 16 mm.
3. Cut the cable to size using cable cutters or a wire stripper. Is the cable damaged? Cut past the damaged section.
4. Use a fitting screwdriver to loosen the screws on one side of the screw terminal.
5. Insert the copper cable wire on one side of the screw terminal.
6. When connecting, make sure the entire copper wire is inside the screw terminal, so that only the plastic casing is visible.
7. Repeat steps 5 and 6 for the other cable. Important: Connect the right colors of the screw terminal together.
8. Tighten the screws again.
9. Place the screw terminal in the middle of the WATERLOCK. It is filled with gel to ensure a 100% waterproof connection.
10. Close the WATERLOCK securely, making sure you hear a “click”.
Important: The WATERLOCK cannot be used to repair in-lite main cables (CBL 14/2 and CBL 10/2).
What is the difference between the EVO FLEX CORNER OUTSIDE and the EVO FLEX CORNER INSIDE?
These two assembly accessories are special mounting brackets for creating curves with a 90-degree angle with the EVO FLEX (1, 2, 3) and consist of two sections. one for the EVO FLEX and the other for the ground cable. If you want to use the EVO FLEX (1, 2, 3) in an outside curve, use the EVO FLEX CORNER OUTSIDE. If you want to use the EVO FLEX (1, 2, 3) in an inside curve, use the EVO FLEX CORNER INSIDE.
Do I need to use a separate EVO FLEX DRIVER 1 for every EVO FLEX?
Yes, a separate EVO FLEX DRIVER 1 is needed for every EVO FLEX. Lock the grey connectors together. It is not possible to connect several EVO FLEX strips together.