FAQ Search Results

The connection fails often, even though it is possible to reconnect each time. How can I improve the connection?
Try the following tips: 1. Reduce the distance to the installed (and previously connected) SMART HUB-150. 2. Disconnect any devices that are connected unnecessarily. 3. Make sure the Bluetooth connection is not disrupted by a material like metal or a microwave or Wi-Fi router.
How can I dim the DISC PENDANT 100-230V?
The DISC PENDANT 100-230V is dimmable by hand movement. The sensor is located on the bottom of the fixture in the middle and is operated by hand approach. Brief touch/approach: On/Off Long touch/approach: Dim The dimmer remembers the last position when switched off manually by the sensor.
Can I reset the SMART EXTENDER?
Yes, you can reset the SMART EXTENDER by holding in the button for 15 seconds until it starts blinking. Important: The SMART EXTENDER is now no longer part of the Garden in the in-lite app. To add it again, go to Settings --> Garden --> SMART EXTENDER.
I no longer need the SMART EXTENDER for part of or my entire Garden. Can I use the SMART EXTENDER for a different Garden?
Yes, you can. Remove the SMART EXTENDER by resetting it. The SMART EXTENDER can now be found for a different Garden. Select the other Garden in the in-lite app under Settings --> Garden and Add the SMART EXTENDER here. Important: A connection to the Garden is needed to add the SMART EXTENDER.
Is the DISC WALL (100-230V) dimmable?
The DISC WALL 12V is not dimmable, but the DISC WALL 100-230V is.
Is the DISC PENDANT (100-230V) dimmable?
The DISC PENDANT 12V is not dimmable, but the DISC PENDANT 100-230V is.
How far apart should I hang the DISC PENDANT (100-230V) lights?
With some clearance. Do not hang the DISC PENDANT (100-230V) lights close together.
Where is the best place to hang the DISC PENDANT (100-230V)?
A place with some clearance. Do not hang the DISC PENDANT in a windy area.
Is the DISC (LOW) dimmable?
No, the DISC (LOW) is not dimmable.
How is the DISC WALL 100-230V dimmed?
With an external LED dimmer only. Connect the DISC WALL 100-230V to an external LED dimmer with trailing edge and a wattage of 2-100W or 3-100W.
Does the DISC PENDANT 100-230V require an external LED dimmer?
No, the DISC PENDANT 100-230V does not require an external dimmer. It is dimmable without an external LED dimmer. In other words, the light does not have to be connected to a switched power outlet.
Can an external switch be connected to the DISC PENDANT 100-230V?
Yes, it can. But this may not be an LED dimmer. Important: If you want to use an external switch, keep in mind that when the switch is in the OFF position, the light cannot be operated by the sensor. Also, the light will be subjected to an automatic calibration process the first 15 seconds each time the external switch is switched from the OFF to the ON position. During this time, do not place a hand or conductive objects near the sensor because this will interfere with calibration.
The cable of my fixture is damaged. Can I repair it?
Absolutely. Use the WATERLOCK accessory. The WATERLOCK lets you repair damaged fixture cables. To fix the cable, perform the following steps: 11. First make sure that the power supply to the cable is switched off. 12. Use small 4/6 mm² screw terminals no larger than 18 mm x 12 mm x 16 mm. 13. Cut the cable to size using cable cutters or a wire stripper. Is the cable damaged? Cut past the damaged section. 14. Use a fitting screwdriver to loosen the screws on one side of the screw terminal. 15. Insert the copper cable wire on one side of the screw terminal. 16. When connecting, make sure the entire copper wire is inside the screw terminal, so that only the plastic casing is visible. 17. Repeat steps 5 and 6 for the other cable. Important: Connect the right colors of the screw terminal together. 18. Tighten the screws again. 19. Place the screw terminal in the middle of the WATERLOCK. It is filled with gel to ensure a 100% waterproof connection. 20. Close the WATERLOCK securely, making sure you hear a “click”. Important: The WATERLOCK cannot be used to repair in-lite main cables (CBL 14/2 and CBL 10/2).
Can the DISC PENDANT 100-230V fixtures that are combined using the DISC BASE TRIPLE be operated separately?
Yes, they can. The DISC PENDANT 100-230V fixtures can be operated separately.
I've accidentally cut my fixture cable. Can I fix it?
Absolutely. Use the WATERLOCK accessory. The WATERLOCK lets you repair cut fixture cables. To fix the cable, perform the following steps: 1. First make sure that the power supply to the cable is switched off. 2. Use small 4/6 mm² screw terminals no larger than 18 mm x 12 mm x 16 mm. 3. Cut the cable to size using cable cutters or a wire stripper. Is the cable damaged? Cut past the damaged section. 4. Use a fitting screwdriver to loosen the screws on one side of the screw terminal. 5. Insert the copper cable wire on one side of the screw terminal. 6. When connecting, make sure the entire copper wire is inside the screw terminal, so that only the plastic casing is visible. 7. Repeat steps 5 and 6 for the other cable. Important: Connect the right colors of the screw terminal together. 8. Tighten the screws again. 9. Place the screw terminal in the middle of the WATERLOCK. It is filled with gel to ensure a 100% waterproof connection. 10. Close the WATERLOCK securely, making sure you hear a “click”. Important: The WATERLOCK cannot be used to repair in-lite main cables (CBL 14/2 and CBL 10/2).
Page
Back to top